Engineers verifying a wall of smart meters in a meter room
Metering10 November 2026·6 min read

Smart meter verification: how to prove your electricity bills are right

A bill is only as reliable as the meter behind it. Check three things: is the meter accurate, is it set up correctly, and do the readings add up?

In this article
  1. Accuracy, explained
  2. Layer 1: Is the meter accurate?
  3. Layer 2: Is it set up correctly?
  4. Layer 3: Do the readings add up?
  5. A verification procedure
  6. Why it matters
  7. Faults that look like a billing dispute
  8. How AVEX GRID helps

Key points

  • There are three checks: is the meter accurate, is it set up correctly, and do the readings add up.
  • Accuracy is tested by comparing the meter with a calibrated reference under a known load.
  • A wrong multiplier or current transformer setting can make a bill look like real consumption.
  • In a building, the sub-meters plus common areas and losses should match the main meter. A steady gap needs investigating.
  • A written verification gives landlords and tenants a fair basis for billing and settles disputes quickly.

Smart meters and prepaid meters have spread across homes, shops, offices and factories. When they are installed and set up correctly, they record accurately. Disputes start when something is wrong. The difficulty is that a wrong number looks exactly like a right one. Verification is the process that tells them apart.

Accuracy, explained

A meter's accuracy is given as a percentage error: how far its reading is from the true value, as a share of the true value. A meter that shows 1,015 kWh when the true figure is 1,000 kWh is 1.5% fast.

The accuracy class of a meter is a rating, such as class 1, that says how large an error is allowed. For a static energy meter, the class is the limit of that error at reference conditions. A class 1 meter may be wrong by up to 1% either way. A class 2 meter may be wrong by up to 2%. These limits come from IEC 62053-21. IEC is the International Electrotechnical Commission, which writes international standards for electrical equipment. The limits apply at stated currents, a stated power factor and a stated temperature. Power factor shows how much of the power you draw is actually useful. So a meter that is within class at full load can be outside it at light load. Some meters are connected through current and voltage transformers. Their errors add to the meter's. For small errors, the total is close to the meter error plus the transformer errors added together.

The money value is easy to work out. A plant buys 180,000 kWh a month at 11 US cents per kWh, and pays US$19,800. A kWh, or kilowatt-hour, is the energy of 1,000 watts used for one hour. It is the unit your meter counts and your bill charges for. Suppose the combined error is +1.5%. That is 180,000 × 1.5% = 2,700 kWh. It costs about US$297 a month and US$3,564 a year, and nothing on the bill shows that something is wrong. Current transformers made for metering, for example class 0.5S under IEC 61869-2, keep the transformer share of the error small.

Layer 1: Is the meter accurate?

Electricity meters are built to set accuracy classes under standards such as the IEC 62053 series. A verification is a check by an independent person that the figures are true and the method was followed. In a meter test, you compare the meter under test with a calibrated reference meter. Both are connected to the same load. The result is the percentage error at one or more load points. Test points usually include low, medium and high load, and different power factors, because errors can change with load.

Permitted error of an electricity meter, by accuracy classPercent error allowed at rated conditions
2%Class 2
1%Class 1
0.5%Class 0.5S
0.2%Class 0.2S

Larger customers and revenue-grade metering use the tighter classes. Source: IEC 62053 series, static meters

Layer 2: Is it set up correctly?

A meter that is accurate can still produce the wrong bill if it is set up wrongly. The usual causes are listed below.

Configuration itemWhat goes wrong
Current-transformer ratioA wrong ratio multiplies every reading by the wrong factor
Meter multiplier or constantBilled units differ from true units
Wiring and phase sequenceReversed or swapped connections cause low, negative or unbalanced readings
Tariff programmingTime-of-use bands or rates set incorrectly
Clock and dateIntervals recorded in the wrong period

Layer 3: Do the readings add up?

Take a building with sub-meters. The energy recorded at the main meter should equal the sum of all the sub-meters, plus the common-area use, plus the losses in the building's internal network. A reconciliation compares the two over a month.

Worked exampleThe main meter records 50,000 kWh. The sub-meters of the tenants, who rent space and are billed for the power they use, total 44,000 kWh. The landlord's common areas use 3,500 kWh. That leaves 2,500 kWh, or 5%, as network losses and unmetered use. A gap of 5% may be normal for that installation. A gap that grows from month to month deserves investigation.

A verification procedure

  1. Inventory. List every meter, with its location, type, serial number, ratio and the circuit it serves.
  2. Check the setup. Read the programmed ratios, multipliers and tariffs. Compare them with the installation.
  3. Test accuracy. Compare selected meters with a reference at set load points.
  4. Reconcile. Compare the main meter with the sum of the sub-meters over at least one billing period.
  5. Report. Record the findings, the corrections and the evidence, so both sides can rely on them.

Why it matters

  • Fairness. Tenants pay for what they use. Landlords recover what they spend.
  • Settling disputes. A documented test settles a disagreement faster than an argument.
  • Finding losses. A growing gap can reveal faulty meters, wiring errors or connections that nobody meters.
  • Solar and net metering. Net metering is an arrangement where you send your extra solar power to ZETDC and it is set off against what you take from the grid. Meters that read in both directions must record import and export correctly for this to work.

Faults that look like a billing dispute

Most complaints trace back to a short list of causes. Knowing them speeds up the diagnosis, because each one leaves a different pattern in the numbers.

  • Wrong current-transformer ratio. The meter multiplies what it measures by the ratio programmed into it. If that ratio does not match the transformers actually installed, every reading is wrong by the same factor. A bill that is exactly double, or exactly half, of what you expected is the classic sign.
  • Wrong multiplier on the bill. The meter is correct, but the billing system uses the wrong constant. The error is again a clean multiple. It appears from the first bill after the change.
  • Reversed or mis-phased current transformer. One phase is subtracted instead of added, or the voltage and current are paired with the wrong phases. The meter reads too low, usually by a third or more, and the error moves with load.
  • Shared circuits. A tenant meter might also feed a neighbour's socket, a pump or a signboard. Then it records energy the tenant did not use. Only a walk through the wiring finds this.
  • Clock and tariff settings. A tariff is the price list for electricity: the rates per unit, per kVA and the fixed charges. A meter with the wrong date, time or tariff table puts energy in the wrong period. The total energy is right, but the cost is not.
  • Prepaid credit logic. Tokens loaded, fixed charges deducted and arrears recovered can make the credit fall faster than the use alone would suggest. The vendor's statement shows the split.

Read the pattern before you test anything. A constant ratio between billed and expected energy points to a ratio or multiplier error. A gap that grows with load points to accuracy or phasing. A gap that appears only at certain hours points to a clock or tariff setting. Starting from the pattern usually saves a day of testing.

How AVEX GRID helps

  • Meter inventory and setup review for buildings, estates and factories.
  • Accuracy testing and reconciliation with a written report.
  • Billing method that shares energy, demand and common costs in a way that tenants can follow.

What AVEX GRID can take off your hands

AVEX GRID is an engineer-led energy consultancy in Zimbabwe. We do the technical work that turns an energy investment into a plant that is licensed, connected, financed and performing, whether you are a local operator or an investor overseas.

Feasibility and bankable studiesYield, load and hybrid models, and the technical file lenders and ZERA read.
Power-system engineering (ETAP)Load flow, short circuit, arc flash and protection studies for approvals and safe design.
Licence and PPA technical supportZERA licence documents, ZETDC connection studies, PPA technical schedules.
Owner's engineerDesign review, testing and commissioning on your side of the EPC table.
Tariff, audit and compliance workMaximum-demand and power-factor savings, readiness for energy-management rules.
Remote plus on the groundModelling for overseas teams, with an engineer in Zimbabwe for site, utility and regulator work.

We quote fixed prices after a free scoping call and reply the same working day.

Frequently asked questions

What does accuracy class 1 mean?

That the meter is permitted a percentage error of plus or minus 1% under reference conditions, as set out in IEC 62053-21. The limit applies at stated currents and power factor, and the errors of any current or voltage transformers add to it.

How often should a meter be tested?

It depends on the meter type, the regulations that apply and the value of the load. Large industrial meters are tested more often than small ones. We recommend a schedule for each site.

What if the sum of sub-meters is higher than the main meter?

That points to a configuration error or a faulty meter, because sub-meters cannot measure more energy than entered the building. It should be investigated promptly.

Can a prepaid meter be verified?

Yes. The accuracy and configuration checks apply, together with a review of how credit and tariffs are programmed.

Does verification need a shutdown?

Often not. Many tests can be done on a live installation with the proper safety controls, and any interruptions are planned with the site.

Topics: smart meter verificationmeter accuracy testsub-metering reconciliationtenant electricity billingprepaid meter checkIEC 62053meter audit Zimbabweenergy consultant Zimbabwe

Sources and notes

General information to help you plan. The rules that apply to your site are confirmed by AVEX GRID against the current gazetted text, ZERA and ZETDC as part of the work. The sources used are listed below.

DJ

Devine Tafara Javangwe is the founder and lead consulting engineer at AVEX GRID. He holds an MSc in Electrical Power Engineering (Southern Federal University, 2025), is a Professional Member of the Zimbabwe Institution of Engineers and an IEEE member.

About the practice · Contact

Make your meter readings defensible.

Send us the meter layout and a recent bill. We propose a verification plan and the report you can show tenants, auditors or the utility.

+263 78 488 9775 · Autherstone Street 21, Marondera, Zimbabwe · Remote across Southern Africa